Rav’s Steels rotary kiln and plant structure

High-metallic sponge iron, made with care.

Rav’s Steels Private Limited makes coal-based sponge iron from 63% Fe pellets or 61% Fe iron ore and RB2 coal, at Ananthapuram, Andhra Pradesh.

200 TPDAbout 60,000 tonnes a year
80% Fe(M)Sponge iron lumps, 4–20 mm
72% Fe(M)Sponge iron fines, 0–4 mm
RB2 coalUsed exclusively

About us

Rav’s Steels Private Limited is a registered manufacturer at Hirdehal Village, D. Hirehal Mandalam, Raydurgam Taluk, Ananthapuram District, Andhra Pradesh.

We make sponge iron, also called direct reduced iron (DRI), in a rotary kiln. High-grade feed of 63% Fe pellets or 61% Fe iron ore gives highly metallic sponge iron and better recovery at your furnace. Our plant capacity is 200 tonnes per day.

Our customers are induction furnace units, steel melt shops, foundries and traders. Charcoal and iron ore fines recovered in the process are sold as by-products.

Rotary kiln at the Rav’s Steels plant
Our rotary kiln, where iron ore and RB2 coal are converted into sponge iron.

Our products

Two grades of sponge iron, graded by size to suit your furnace charge.

Sponge iron lumps

4–20 mm
80% Fe(M)

Our main grade for melting. High metallic content gives better recovery, and lumps charge easily into induction and arc furnaces.

Sponge iron fines

0–4 mm
72% Fe(M)

The finer fraction from screening. Suited to blended furnace charges, briquetting, foundries and traders.

By-products

Char lumps

4–20 mm · GCV about 3,000 kcal/kg

Burnt in power plants for power generation, like low-grade coal.

Char fines

0–4 mm · GCV about 3,000 kcal/kg

Used as boiler fuel in power plants and by brick plants to make bricks.

Iron ore fines

0–5 mm · 57% Fe

Sold to domestic buyers and for export, for sintering and pellet making.

At a glance

ProductSizeGradeUsed for
Sponge iron lumps4–20 mm80% Fe(M)Induction and arc furnaces
Sponge iron fines0–4 mm72% Fe(M)Blended charge, briquetting
Char lumps4–20 mmGCV about 3,000 kcal/kgPower plant fuel
Char fines0–4 mmGCV about 3,000 kcal/kgPower plant fuel, bricks
Iron ore fines0–5 mm57% FeSintering, pellets, export

Fe(M) means metallic iron. Total Fe, carbon, sulphur and phosphorus are available in our test reports on request. All products are supplied in bulk by truck.

Our process

Coal removes the oxygen from iron ore inside a rotary kiln. The iron is reduced in the solid state and is never melted.

StockyardCrushingCoolerMagneticseparatorProductbinsRotary kiln
PreheatingUp to about 800 °C
ReductionAbout 950–1050 °C
CoolingBelow about 100 °C
1

Receiving

63% Fe pellets or 61% Fe ore and RB2 coal are weighed, sampled and stored separately. Coal stays covered and dry.

2

Crushing and screening

Ore is sized for the kiln. Coal is split into feed coal and finer coal for injection along the kiln.

3

Weighed feeding

Belt weigh feeders send ore and coal at a fixed ratio into the kiln inlet for a steady process.

4

Travel through the kiln

The slightly inclined kiln turns slowly and moves the charge from inlet to discharge, typically in 8–10 hours.

5

Temperature control

Thermocouples along the shell track every zone. Combustion air and coal injection are adjusted to hold the reduction zone steady.

6

Cooling

A sealed rotary cooler with water on the outer shell cools the product, typically in about 1 hour, so it does not re-oxidise.

7

Magnetic separation

Magnetic separators pull out sponge iron. Char and ore fines, which are non-magnetic, are collected separately.

8

Sizing and dispatch

Sponge iron is screened into lumps and fines, stored in separate bins, sampled in the lab and loaded.

9

Clean exhaust

Kiln waste gas passes through a settling chamber and gas cleaning before it leaves the stack.

Temperatures and times are typical for coal-based rotary kiln plants.

Why choose Rav’s Steels

High-grade feed

63% Fe pellets or 61% Fe iron ore for highly metallic sponge iron.

RB2 coal only

South African RB2 coal gives consistent reduction.

Two clear grades

Lumps at 4–20 mm and fines at 0–4 mm, with stated metallic iron.

Reliable volume

200 tonnes per day for regular monthly supply.

Useful by-products

Char for power plants and brick makers, and iron ore fines for domestic and export buyers.

Direct from the plant

Supplied straight from our plant at Ananthapuram, with no middlemen.

Quality control

Kiln feed structure and chimney at the plant

Every lot is sampled in our laboratory before it leaves the plant. We check:

Total Fe, metallic Fe, carbon, sulphur and phosphorus.
Size, by screen analysis of lumps and fines.
Magnetic content, so non-magnetic waste stays low.

A test report can be shared with each consignment on request.

Request a quote

Tell us the product, monthly quantity and delivery location. We will reply with price and availability.

Plant address

M/s. Rav’s Steels Private Limited
Sy. No. 5, 7 & 8, Hirdehal Village,
D. Hirehal Mandalam, Raydurgam Taluk,
Ananthapuram District, Andhra Pradesh – 515872

Open in Google Maps

Contact

Phone: 9353944480
Email: rspl1965@gmail.com

Registration

UDYAM: UDYAM-KR-05-0000677 (Small, Manufacturing)
GSTIN: 37AAECR0908H1ZH
State: Andhra Pradesh, Code 37